D-Link DWL-3200AP - AirPremier - Wireless Access Point Product Manual Download

Page: 78 / 113

DWL-3200AP User’s Manual

D-Link Systems, Inc.

Using the AP Manager

To upgrade the ﬁrmware:

Download the latest ﬁrmware upgrade from http://support.dlink.com

to an easy to ﬁnd location on your hard drive.

Click on the ﬁrmware button as shown above.

A popup window will appear. Locate the ﬁrmware upgrade ﬁle and

click

Open

You can upgrade the ﬁrmware by clicking on this button after
selecting the device(s).

Firmware



IMPORTANT! DO NOT DISCONNECT POWER FROM THE UNIT WHILE THE
FIRMWARE IS BEING UPGRADED.

Summary of Contents for DWL-3200AP - AirPremier - Wireless Access Point


















































































































Search results

Summary of Contents for DWL-3200AP - AirPremier - Wireless Access Point

Reviews:

Related manuals for DWL-3200AP - AirPremier - Wireless Access Point

Brands by name

Popular brands

D-Link DWL-3200AP - AirPremier - Wireless Access Point, Product Manual

Search results

Summary of Contents for DWL-3200AP - AirPremier - Wireless Access Point

Reviews:

Related manuals for DWL-3200AP - AirPremier - Wireless Access Point

Brands by name

Popular brands