D-Link DIR-660 User Manual Download | Manualshive

Page: 80 / 98

background image

0

D-Link DIR-660 User Manual

Section 6 - Troubleshooting

• Configure your Internet settings:

• Go to

Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab,

click the button to restore the settings to their defaults.

• Click the

Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings

button. Make sure nothing is checked. Click

OK.

• Go to the

Advanced tab and click the button to restore these settings to their defaults. Click OK three

times.

• Close your web browser (if open) and open it.

• Access the web management. Open your web browser and enter the IP address of your D-Link router in the address

bar. This should open the login page for your the web management.

• If you still cannot access the configuration, unplug the power to the router for 10 seconds and plug back in. Wait

about 30 seconds and try accessing the configuration. If you have multiple computers, try connecting using a different
computer.

2. What can I do if I forgot my password?

If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back
to the factory defaults.

To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a
paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process.
Wait about 30 seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is
admin and leave the password box empty.

«
...
78
79
80
81
82
...
»

Summary of Contents for DIR-660



































































































Reviews:

No comments

Related manuals for DIR-660

Brand: Ublox Pages: 43

Brand: Tenda Pages: 34

Brand: Arris Pages: 2

Brand: Konig Pages: 2

Brand: TP-Link Pages: 2

Pepwave Surf SOHO

Brand: peplink Pages: 151

Brand: Z-Com Pages: 38

Brand: IBM Pages: 44

WAP54G - Wireless-G Access Point

Brand: Linksys Pages: 84

TEW-434APB - 54Mbps Wireless G PoE Access Point

Brand: TRENDnet Pages: 2

WAP11 - Instant Wireless Network Access Point

Brand: Linksys Pages: 33

NUCLIAS CONNECT DAP-2680

Brand: D-Link Pages: 48

Brand: D-Link Pages: 24

Brand: D-Link Pages: 24

Brand: D-Link Pages: 24

Brand: D-Link Pages: 25

Brand: D-Link Pages: 26

nuclias connect DAP-2662

Brand: D-Link Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands