D-Link DIR-660 User Manual Download

Page: 19 / 98

D-Link DIR-660 User Manual

Section - Configuration

Select

Static if your ISP assigned you the IP address,

subnet mask, gateway, and DNS server addresses. In most
cases, select

Dynamic.

Enter the IP address (Static PPTP only).

Enter the Primary and Secondary DNS Server Addresses
(Static PPTP only).

Enter the Gateway IP Address provided by your ISP.

Enter the Server IP provided by your ISP (optional).

Enter your PPTP username.

Enter your PPTP password and then retype the password
in the next box.

Select either

Always-on, On-Demand, or Manual.

Enter a maximum idle time during which the Internet
connection is maintained during inactivity. To disable this
feature, enable Auto-reconnect.

The DNS server information will be supplied by your ISP
(Internet Service Provider.)

Address Mode:

PPTP IP Address:

PPTP Subnet

Mask:

PPTP Gateway:

PPTP Server IP:

Internet Setup

PPTP

Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with
a username and password. This option is typically used for DSL services.

Username:

Password:

Reconnect Mode:

Maximum Idle

Time:

DNS Servers:

Summary of Contents for DIR-660



































































































Search results

Summary of Contents for DIR-660

Reviews:

Related manuals for DIR-660

Brands by name

Popular brands

D-Link DIR-660, User Manual

Search results

Summary of Contents for DIR-660

Reviews:

Related manuals for DIR-660

Brands by name

Popular brands