D-Link DIR-660 User Manual Download

Page: 60 / 98

D-Link DIR-660 User Manual

Section - Configuration

This page displays the current information for the DIR-660. It will display the LAN, WAN (Internet), and Wireless
information.

If your Internet connection is set up for a Dynamic IP address then a

Release button and a Renew button will be

displayed. Use

Release to disconnect from your ISP and use Renew to connect to your ISP.

If your Internet connection is set up for PPPoE, a

Connect button and a Disconnect button will be displayed. Use

Disconnect to drop the PPPoE connection and use Connect to establish the PPPoE connection.

Displays the router’s time and firmware version.

Displays the MAC address and the public IP settings for the router.

Displays the MAC address and the private (local) IP settings for the
router.

Displays the wireless MAC address and your wireless settings such as
SSID and Channel.

Displays computers and devices that are connected to the router via
Ethernet and that are receiving an IP address assigned by the router
(DHCP).

Displays the Multicast Group IP Address.

General:

WAN:

LAN:

Wireless LAN:

LAN Computers:

IGMP Multicast

Memberships:

Device Information

Summary of Contents for DIR-660



































































































Search results

Summary of Contents for DIR-660

Reviews:

Related manuals for DIR-660

Brands by name

Popular brands

D-Link DIR-660, User Manual

Search results

Summary of Contents for DIR-660

Reviews:

Related manuals for DIR-660

Brands by name

Popular brands