D-Link DIR-456 User Manual Download Page 79

Page: 79 / 92

D-Link DIR-456 User Manual

Section 5 - Connecting to a Wireless Network

Connecting to a Wireless Network

Using Windows

Windows

XP users may use the built-in wireless utility (Zero Conﬁguration Utility). The following instructions are for

Service Pack 2 users. If you are using another company’s utility or Windows

2000, please refer to the user manual

of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option
similar to the Windows

XP utility as seen below.

1. If you receive the

Wireless Networks Detected

bubble, click

on the center of the bubble to access the utility.

Right-click on the wireless computer icon in the system tray
in the lower-right corner of the screen. Select

View Available

Wireless Networks

2. The utility will display any available wireless networks in your

area. Click on a network (displayed using the SSID) and click
the

Connect

button.

If you get a good signal but cannot access the Internet,

check you TCP/IP settings for your wireless adapter. Refer
to the

Networking Basics

section in this manual for more

information.

Summary of Contents for DIR-456





























































































Search results

Summary of Contents for DIR-456

Reviews:

Related manuals for DIR-456

Brands by name

Popular brands

D-Link DIR-456, User Manual

Search results

Summary of Contents for DIR-456

Reviews:

Related manuals for DIR-456

Brands by name

Popular brands