D-Link DIR-456 User Manual Download Page 90

Page: 90 / 92

D-Link DIR-456 User Manual

Appendix C - Technical Speciﬁcations

Technical Speciﬁcations

GSM Band (GSM/GPRS/EDGE)

850 / 900 / 1800 / 1900 MHz

Power Class 4 (850 / 900 MHz)

Power Class 1 (1800 / 1900 MHz)

UMTS/HSDPA Band *

850 / 1900 / 2100 MHz

Power Class 3

Data Rates **

6/9/11/12/18/24/36/48/54Mbps in 802.11g mode

1/2/5.5/11Mbps in 802.11b mode

Standards

802.11g

802.11b

802.3

802.3u

Wireless Security

64/128-bit WEP (Wired Equivalent Privacy)

WPA & WPA2 (Wi-Fi Protected Access)

Firewall

Network Address Translation (NAT)

Stateful Packet Inspection (SPI)

VPN

L2TP/PPTP/IPSEC VPN Pass-through

5 Dedicated IPSec tunnels

Antenna

3 Internal antennas

Ports

2 x LAN (RJ-45)

1 x WAN (RJ-45)

1 x Phone (RJ-11)

USIM Slot

Standard 6-pin SIM card interface

LED Status Indicators

WPS

WAN

LAN

WLAN

2G/2.5G

3G/3.5G

SMS

Signal

3 Internal antennas

(2 for 3G, 1 for WIFI)

Summary of Contents for DIR-456





























































































Search results

Summary of Contents for DIR-456

Reviews:

D-Link DIR-456, User Manual, Page: 90 / 92

Search results

Summary of Contents for DIR-456

Reviews: