manualshive.com logo in svg

D-Link dgs-8000 SERIES, Hardware Installation Manual, Page: 54 / 97

Share
Download
D-Link dgs-8000 SERIES Hardware Installation Manual Download Page 54

DGS-8000 Series Hardware Installation Guide                                     Chapter 3 Switch Installation 

 

47 

 

(1) Insert the air filter along the guide rail and tighten the captive screws on the air filter. 

(2) Install the plastic dust cap before the air filter by pressing firmly the two buttons of the 
plastic dust cap on the both sides. 

The simple steps for removing the air filters of the host management module and service 
module on the DGS-8010 are as follows: 

(1) Press the buttons of the plastic dust cap to the bottom and remove the plastic dust cap. 

(2) Loosen the captive screws on the air filter. 

(3) Take out the air filter. 

 

Figure 3-3 Installation location for the air filters of the host management module and 

service module on the DGS-8010 

 

 

①

Plastic dust cap before the air filter installation location 

 Buttons on the plastic 

②

dust cap 

 

Note 

The dust in the air may block the air outlet of an air filter after an air filter is 
used for a long time, thus affecting system ventilation and heat dissipation. It 
is recommended to clear it once per three months. 

 

Summary of Contents for dgs-8000 SERIES


































































































Reviews:

No comments