manualshive.com logo in svg

D-Link dgs-8000 SERIES, Hardware Installation Manual, Page: 38 / 97

Share
Download
D-Link dgs-8000 SERIES Hardware Installation Manual Download Page 38

DGS-8000 Series Hardware Installation Guide                                     Chapter 1 Product Overview 

 

31 

 

Highest 
rotation speed 

5400RPM 5400RPM 

Power 
consumption 

240W 160W 

Weight  

6.0kg (net) 

4.0kg (net) 

Dimensions (L 
x W x H) 

431.6 x 396.2 x 44 mm 

312.3 x 298 x 64.4 mm 

1.4.9  

  8000-1400AC/8000-2000AC Power 

Supply Module 

1.4.9.1 

 

Introduction 

The 8000-1400AC/8000-2000AC is an AC power supply module and can provide 110/220V 
AC power supply input interfaces for the DGS-8006/8010. 

1.4.9.2 

 

LEDs on the Module Panel 

Table 1-19 LEDs on the front panel 

LED 

Identifier 

Status 

Meaning 

Off

 

No input power supply 

Input state 
LED 

IN

 

Solid 
Green

 

The input power supply is normal. 

Off 

No output power supply 

Output state 
LED 

OUT 

Solid 
Green 

The output power supply is normal. 

Off

 

The power supply works normally. 

Power 
supply fault 
LED 

FAIL 

Solid Red

There is a fault within the power supply. 

 

1.4.9.3 

 

Technical Specifications 

Table 1-20 8000-1400AC/8000-2000AC technical specifications 

  AC Power Supply Parameter 

Module 
Model 

8000-1400AC 

8000-2000AC 

Rated voltage 
range 

100-120V~, 200-240V~; 50/60Hz 

100-120V~, 200-240V~; 50/60Hz 

Summary of Contents for dgs-8000 SERIES


































































































Reviews:

No comments