manualshive.com logo in svg

Cygnus M3-DIVE, Operation Manual

Share
Download
Cygnus M3-DIVE Operation Manual Download Page 96

Cygnus DIVE Operating Manual 

M3-DIVE-M-ENG_Iss9.docx 

 

Page 96 of 117 

 

Type this into Google search  “

FTDI USB RS485 Cable

”

 

 
Or follow this link directly to the FTDI website; 
 

http://www.ftdichip.com/Products/Cables/USBRS485.htm

 

 

Click on the 

VCP Drivers

 link; 

 
You will see a table of drivers with the most recent at the top. The 
x86 (32bit) driver is recommended. 

 
There is a green and red LED inside the USB connector end of the 
cable 

–

 when installed correctly the green LED will flash every time 

the DIVE gauge sends data, the red LED will flash when CygLink 
sends data to the DIVE gauge. 

Wiring Problems 

Sometimes the cable between the DIVE gauge and the USB 
converter is damaged, or has been repaired incorrectly. Although 
there are only 2 data wires they must be connected the correct 
way around. Double check the 

connections from the gauge’s 

connector to the serial converter connection. 
 
If you have the short serial to USB interface cable 

–

 check the 

gauge can connect to CygLink using this cable 

–

 if it works then 

the USB driver must be ok, the problem may lie in the long 

umbilical cable. 
 
 

Summary of Contents for M3-DIVE






















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands