manualshive.com logo in svg

Cygnus M3-DIVE, Operation Manual

Share
Download
Cygnus M3-DIVE Operation Manual Download Page 72

Cygnus DIVE Operating Manual 

M3-DIVE-M-ENG_Iss9.docx 

 

Page 72 of 117 

15.

 

HelmetView Remote Display 

HelmetView is an optional remote display that can be mounted on 
a Kirby Morgan

®

 dive helmet using an accessory screw. The 

display will show the measured thickness value or the echo bars 

just like the DIVE’s display. HelmetView enables the diver to view 

thickness measurements in limited visibility or black water. 
 

 

 

 

HelmetView is supplied as a remote display unit with 1.5 meters of 
cable with connector and a mounting bracket to suit the Kirby 
Morgan

®

 helmets. 

 
HelmetView is simply plugged into the spare connector on the 

opposite side to the probe cable. When the DIVE gauge is turned 
on the remote display will 

reflect the gauge’s display.

 

 

Fitting the Mounting Bracket 

The mounting bracket is screwed to the rear of the HelmetView 
display using two M3 x 6mm screws. 

 

Summary of Contents for M3-DIVE






















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands