CyberResearch MMGA Series User Manual Download Page 80

Page: 80 / 286

MMGA Series

CyberResearch

Motherboards

CyberResearch, Inc.

Figure 1-30: Front Panel Connector Pinout Locations (14-pin)

FUNCTION PIN DESCRIPTION FUNCTION PIN DESCRIPTION

1 +5V

2 +5V

3 N/C

4 N/C

Power LED

5 GROUND

6 N/C

Speaker

8 SPEAKER

Power

Button

9 PWRBTN-

N/C

11 +5V

12 RESET-

HDD LED

13 IDE

LED-

Reset

14 GROUND

Table 1-16: Front Panel Connector Pinouts (14-pin)

4.2.10 Infrared Interface Connector

CN Label:

IR1

CN Type:

5-pin header (1x5)

CN Location:

See

Figure 1-31

CN Pinouts:

See

Table 1-17

The infrared interface connector supports both Serial Infrared (SIR) and Amplitude Shift

Key Infrared (ASKIR) interfaces.

Summary of Contents for MMGA Series














































































































































































































































































Search results

Summary of Contents for MMGA Series

Reviews:

Brands by name

Popular brands

CyberResearch MMGA Series, User Manual

Search results

Summary of Contents for MMGA Series

Reviews:

Brands by name

Popular brands