CyberResearch MMGA Series User Manual Download Page 25

Page: 25 / 286

CyberResearch

Motherboards

MMGA

Series

CyberResearch, Inc

25 Business Park Drive

P: (203) 643-5000; F: (203) 643-5001

Branford, CT USA

www.cyberresearch.com

1.1.1 MMGA Features

Some of the MMGA features are listed below.

Supports the following Intel® LGA775 processors:

Intel® Core™2 Duo (45nm and 65nm)

Intel® Core™2 Quad (45nm and 65nm)

Intel® Celeron® (65nm)

Supports four 240-pin 2 GB 667 MHz or 800 MHz DDR2 DIMMs

Six SATA II drives with transfer rates of 3.0 Gbps supported

Twelve USB 2.0 devices supported (eight onboard and four on the rear panel)

Dual GbE Ethernet connectors

uATX form factor

RoHS compliant

Supports ATX power supplies

1.2 MMGA Overview

1.2.1 MMGA Overview Photo

The MMGA has a wide variety of peripheral interface connectors.

Figure 1-2

is a labeled

photo of the peripheral interface connectors on the MMGA.

Summary of Contents for MMGA Series














































































































































































































































































Search results

Summary of Contents for MMGA Series

Reviews:

Brands by name

Popular brands

CyberResearch MMGA Series, User Manual

Search results

Summary of Contents for MMGA Series

Reviews:

Brands by name

Popular brands