CyberResearch MMGA Series User Manual Download Page 104

Page: 104 / 286

MMGA Series

CyberResearch

Motherboards

CyberResearch, Inc.

Figure 1-48: Insert the Socket LGA775 CPU

Step 8:

Close the CPU socket.

Close the load plate and engage the load lever by

pushing it back to its original position. Secure the load lever under the retention

tab on the side of CPU socket.

Step 9:

Connect the CPU 12V cable to the 12V power.

After the cooling kit is installed

connect the CPU cable to the CPU 12V power connector.

Step 0:

5.4.2 Socket LGA775 Cooling Kit Installation

WARNING:

It is strongly recommended that you DO NOT use the original heat

sink and cooler provided by Intel® on the MMGA.

The cooling kit includes a support bracket that is combined with the

heat sink mounted on the CPU to counterweigh and balance the load

on both sides of the PCB.

Summary of Contents for MMGA Series














































































































































































































































































Search results

Summary of Contents for MMGA Series

Reviews:

Brands by name

Popular brands

CyberResearch MMGA Series, User Manual

Search results

Summary of Contents for MMGA Series

Reviews:

Brands by name

Popular brands