CyberResearch MMGA Series User Manual Download Page 70

Page: 70 / 286

MMGA Series

CyberResearch

Motherboards

CyberResearch, Inc.

Connector

Type

Label

Audio connector

Audio jack

AUDIO_CV1

Ethernet and dual USB combo connector

RJ-45 and two USB

LAN1_USB01

Ethernet and dual USB combo connector

RJ-45 and two USB

LAN2_USB23

Mouse or keyboard connector

PS/2

KB_MS1

Parallel port, serial port and VGA combo

connector

DB-25, DB-9 and

DB-15

3IN1_DSUB1

Table 1-7: Rear Panel Connectors

4.2 Internal Peripheral Connectors

Internal peripheral connectors are found on the motherboard and are only accessible

when the motherboard is outside of the chassis. This section has complete descriptions of

all the internal, peripheral connectors on the MMGA.

4.2.1 ATX Power Connector

CN Label:

ATX1

CN Type:

24-pin ATX (2x12)

CN Location:

See

Figure 1-22

CN Pinouts:

See

Table 1-8

The ATX connector is connected to an external ATX power supply. Power is provided to

the system, from the power supply through this connector.

Summary of Contents for MMGA Series














































































































































































































































































Search results

Summary of Contents for MMGA Series

Reviews:

Brands by name

Popular brands

CyberResearch MMGA Series, User Manual

Search results

Summary of Contents for MMGA Series

Reviews:

Brands by name

Popular brands