CyberResearch MMGA Series User Manual Download Page 225

Page: 225 / 286

CyberResearch

Motherboards

MMGA

Series

CyberResearch, Inc

203

25 Business Park Drive

P: (203) 643-5000; F: (203) 643-5001

Branford, CT USA

www.cyberresearch.com

8.1 Intel

AMT Setup Procedure

The MMGA is featured with the Intel® Active Management Technology (AMT) 3.0. To

enable the Intel® AMT function, follow the steps below.

Step 1:

Make sure the

DIMM1

socket is installed with one DDR2 DIMM.

Step 2:

Connect an Ethernet cable to the RJ-45 connector labeled

LAN2_USB23

Step 3:

The AMI BIOS options regarding the Intel® ME or Intel® AMT must be enabled,

including:

Intel® AMT Configuration [Advanced] (see

Section 6.3.8

)

ME Subsystem Configuration [Advanced] (see

Section 6.3.8.1

)

Step 4:

Configure the Intel® Management Engine BIOS extension (MEBx)

(see

Section 8.2

below)

Step 5:

Properly install the Intel® AMT drives. Make sure to install both HECI and

LMS_SOL drivers from the iAMT Driver & Utility directory in the driver CD (see

Section 7.9

Step 6:

The following dialog window is displayed after the OS is loaded to show the

Intel® AMT status on the MMGA is enabled.

Step 0:

Figure 8-1: Intel® Active Management Technology Status Dialog

Summary of Contents for MMGA Series














































































































































































































































































Search results

Summary of Contents for MMGA Series

Reviews:

Brands by name

Popular brands

CyberResearch MMGA Series, User Manual

Search results

Summary of Contents for MMGA Series

Reviews:

Brands by name

Popular brands