CyberResearch GFC IPM User Manual Download Page 59 | Manualshive

Page: 59 / 90

CyberResearch GFC IPM User Manual Download Page 59

IP address

IP address in the usual dot notation.

Subnet Mask

The net mask of the local network.

Gateway IP address

In case the GFC IPM switch should be accessible from networks other than the local
one, this IP address must be set to the local network router's IP address.

Primary DNS Server IP Address

IP address of the primary Domain Name Server in dot notation. This option may be
left empty, however the GFC IPM switch will not be able to perform name resolution.

Secondary DNS Server IP Address

IP address of the secondary Domain Name Server in dot notation. It will be used in
case the Primary DNS Server cannot be contacted.

Remote Console And HTTPS port

Port number at which the GFC IPM switch's Remote Console server and HTTPS
server are listening. If left empty the default value will be used.

HTTP port

Port number at which the GFC IPM switch's HTTP server is listening. If left empty the
default value will be used.

Telnet port

Port number at which the GFC IPM switch's Telnet server is listening. If left empty
the default value will be used.

Bandwidth limitation

The maximum network traffic generated through the GFC IPM switch ethernet
device. Value in Kbit/s.

Enable Telnet access

Set this option to allow accessing the GFC IPM switch using the Telnet
Gateway see the section 6.1.2.

Disable Setup Protocol

Enable this option to exclude the GFC IPM switch from the setup protocol. Setup
protocol is a proprietary layer-2 MAC-based protocol to allow some configuration
software to detect GFC IPM devices in the network, even without IP address, and
then config network related settings to GFC IPM switch..

LAN Interface Settings

The “Autodetect” will set the ethernet speed to the fastest possible value supported

by both endpoints of the link. For example, if you use a 10M/half duplex HUB, this
speed will be auto-selected. If this option does not work with some network device

CyberResearch

®

KVM Accessories

GFC IPM

CyberResearch, Inc

.

57

25 Business Park Drive

P: (203) 643-5000; F: (203) 643-5001

Branford, CT USA

www.cyberresearch.com

«
...
57
58
59
60
61
...
»

Summary of Contents for GFC IPM



























































































Reviews:

No comments