manualshive.com logo in svg

CUSTOM CARE CCUF-844, Installation Instructions & Owner'S Manual

Share
Download
CUSTOM CARE CCUF-844 Installation Instructions & Owner'S Manual Download Page 7

7

3.  CLEAN WATER REGENERATION 

For installations with a high fouling potential, a back flush surge tank and/or a No Hard Water Bypass on the inlet is 

recommended . During regeneration the three way valve will close the normal service inlet and open the inlet from the back 

flush surge tank . The back flush surge tank supplies clean, treated water for regeneration . A 50 gallon (total volume) Pressure 

Tank is advisable . This is the minimum needed tank size to perform a treated water backwash .

CLEAN WATER REGENERATION INSTALLATION

RAW WATER

INLET

NO HARD

WATER BYPASS

(#CV3070FM)

EXPANSION

TANK

FRESH

WATER TANK

5

MICRON

FILTER

CHECK

FRESH

WATER TANK

EXPANSION

TANK

SHUT-OFF/

DRAIN VALVE

TREATED

WATER

OUTLET

TREATED

WATER

OUTLET

The following parts are required for this 

installation but are not included with the unit. 

•  Lower tank shut-off valve

•  Spring Assisted Check valve (see drawing 

for location)

•   No Hard Water Bypass (activated during 

regeneration) . CV-3070FM

CAUTION:

  The backflush surge tank must be sized to provide enough water for the entire regeneration 

whether an auto flush kit is installed or the chlorine generator option is used.

*See additional programming settings section on pages 29-30 of this manual for more information regarding this installation.

RAW WATER

INLET

NO HARD

WATER BYPASS

(#CV3070FM)

EXPANSION

TANK

FRESH

WATER TANK

5

MICRON

FILTER

CHECK

FRESH

WATER TANK

EXPANSION

TANK

SHUT-OFF/

DRAIN VALVE

TREATED

WATER

OUTLET

TREATED

WATER

OUTLET

Overhead View

INSTALLATION

Summary of Contents for CCUF-844





































Reviews:

No comments

Brands by name

Popular brands

Load more brands