Curtiss-Wright EXLAR GTX Series Installation & Service Instructions Manual Download Page 18

18

 | GTX Series Actuator Installation & Maintenance Instructions

Curtiss-Wright | Rev D | PN75557 | 10/01/2019

10.0 WARRANTY AND LIMITATION OF LIABILITY

Products are warranted for two years from date of manufacture as 

determined by the serial number on the product label. Labels are 

generated and applied to the product at the time of shipment. The 

first and second digits are the year and the third and fourth digits 

represent the manufacturing week. Product repairs are warranted 

for 90 days from the date of the repair. The date of repair is 

recorded and tracked by individual product serial number.

Exlar Corporation (“Exlar”) warrants its product(s) to the original 

purchaser and, in the case of original equipment manufacturers, 

to their original customer, to be free from defects in material and 

workmanship and to be made only in accordance with Exlar’s 

standard  published  catalog  specifications  for  the  product(s)  as 

published at the time of purchase. Warranty or performance to 

any  other  specifications  is  not  covered  by  this  warranty  unless 

otherwise agreed to in writing by Exlar and documented as part 

of any and all contracts, including but not limited to purchase 

orders, sales orders, order confirmations, purchase contracts and 

purchase agreements. In no event shall Exlar be liable or have 

any responsibility under such warranty if the product(s) has been 

improperly stored, installed, used or maintained, or if Buyer has 

permitted  any  unauthorized  modifications,  adjustments  and/or 

repairs to such product(s). Seller’s obligation hereunder is limited 

solely to repairing or replacing (at its opinion), at the factory any 

product(s), or parts thereof, which prove to Seller’s satisfaction to 

be defective as a result of defective materials, or workmanship 

and within the period of time, in accordance with the Seller’s stated 

product warranty (see Terms and Conditions, above), provided, 

however, that written notice of claimed defects shall have been 

given to Exlar within thirty (30) days from the date of any such 

defect is first discovered. The product(s) claimed to be defective 

must be returned to Exlar, transportation prepaid by Buyer, with 

written specification of the claimed defect. Evidence acceptable to 

Exlar must be furnished that the claimed defects were not caused 

by misuse, abuse, or neglect by anyone other than Exlar.

Components such as seals, wipers, bearings, brakes, bushings, 

gears, splines, and roller screw parts are considered wear parts 

and must be inspected and serviced on a regular basis. Any 

damage caused by failure to properly lubricate Exlar products and/

or to replace wear parts at appropriate times, is not covered by this 

warranty. Any damage due to excessive loading is not covered by 

this warranty.

The use of products or components under load such that they 

reach the end of their expected life is a normal characteristic of 

the application of mechanical products. Reaching the end of a 

product’s expected life does not indicate any defect in material or 

workmanship and is not covered by this warranty.

Costs for shipment of units returned to the factory for warranty 

repairs are the responsibility of the owner of the product. Exlar will 

return ship all warranty repairs or replacements via UPS Ground 

at no cost to the customer.

For international customers, Exlar will return ship warranty repairs 

or replacements via UPS Expedited Service and cover the 

associated shipping costs. Any VAT or local country taxes are the 

responsibility of the owner of the product.

The foregoing warranty is in lieu of all other warranties (except as 

Title), whether expressed or implied, including without limitation, 

any  warranty  of  merchantability,  or  of  fitness  for  any  particular 

purpose, other than as expressly set forth and to the extent 

specified herein, and is in lieu of all other obligations or liabilities 

on the part of Exlar.

Seller’s maximum liability with respect to these terms and 

conditions and any resulting sale, arising from any cause 

whatsoever, including without limitation, breach of contract or 

negligence,  shall  not  exceed  the  price  specified  herein  of  the 

product(s) giving rise to the claim, and in no event shall Exlar 

be liable under this warranty otherwise for special, incidental or 

consequential damages, whether similar or dissimilar, of any 

nature arising or resulting from the purchase, installation, removal, 

repair, operation, use or breakdown of the product(s) or any other 

cause whatsoever, including negligence.

The foregoing warranty shall also apply to products or parts 

which have been repaired or replaced pursuant to such 

warranty, and within the period of time, in accordance with 

Seller’s stated warranty.

NO PERSON, INCLUDING ANY AGENT OR REPRESENTATIVE 

OF EXLAR, IS AUTHORIZED TO MAKE ANY REPRESENTATION 

OR WARRANTY ON BEHALF OF EXLAR CONCERNING ANY 

PRODUCTS MANUFACTURED BY EXLAR, EXCEPT TO REFER 

PURCHASERS TO THIS WARRANTY.

Summary of Contents for EXLAR GTX Series





















Reviews: