background image

DESI GN  CON CEPT   

 

Curtis Cabs feature an assembly of parts designed for your vehicle which require  
adjustment and alignment of components to accommodate vehicle variations and  
provide proper weather protection. For accurate installation, proper operation, and 
years of satisfaction, please read and understand the installation instructions. 
 
From all of us at Curtis, we thank you for choosing our product. 

 

 

 
CAB I N STALLAT I ON  

BEFORE YOU  START  

HELPFUL REMINDERS: 

            A. Leave all bolts loose for later adjustment unless otherwise specified. 
            B. Read and understand all instructions before beginning. 
            C. Plastic washers have been supplied to provide a weather seal around 
                all exterior fasteners. The plastic washer should be installed under each 
                bolt head directly against the outside cab surface. Care should be taken 
                not to over tighten the fasteners and damage the plastic washer. 
                Also use metal washers as required. 
           D. Apply a clear silicone sealant to seal any minor gaps that may occur due  
                to vehicle variances. For example, windshield cowl to unitized frames. 
 
 
 

TOOLS REQUIRED: 

           

  

 

3/8” DRIVE RATCHET WITH A 3” EXTENSION 
STANDARD AND METRIC SOCKETS (3/8” DRIVE) 
3/16” ALLEN WRENCH 
ELECTRIC DRILL 
#2 PHILLIPS HEAD BIT TO USE IN DRILL 
#2 AND #3 PHILLIPS HEAD SCREWDRIVERS 
FLAT BLADED SCREWDRIVER 
OPEN END WRENCHES 
SNIPS 

  

  This Curtis Cab is designed and manu- 
  factured for use only as reasonable 

weather protection. This cab is not applicable, nor should 
the cab be considered as protection against roll over, 
collision or other accidents that may result. This cabs is 

NOT

 

a

 

R.O.P.S.

 

cab. 

Extreme

 care should be taken when 

operating and by qualified, experienced operators only

.  

 

Exposure

 

to

 

Carbon

 

Monoxide

 

can

 

Cause

 

illness,

 

serious

 

injury

 

or

 

death.

 

Never operate vehicle if suspicious of Carbon Monoxide. 
Inspect exhaust system for leaks monthly. Leaks can result 
from loose connections, corrosion, cracks or other damage 
to the exhaust manifold. If leaks are found, repair or replace 
exhaust system. Do not use vehicle until repair or replace- 
ment is complete. 

  drive r a nd pa sse nge r.

  e x c e e d t he  ve hic le s ra t e d c a pa c it y inc luding

  from  t he  ve hic le s ra t e d c a pa c it y a nd ne ve r

  broc hure s. De duc t  t he  a c c e ssorie s t ot a l w e ight

  Curt is a c c e ssory w e ight s a re  list e d in produc t

  a dd a ddit iona l w e ight  t o t he  ba se  ve hic le . All

  Curt is Ca bs, bla de s a nd ge ne ra l a c c e ssorie s

ADDED

WEI GH T

p. 2 of 16 

Summary of Contents for 1JD2520AS

















Reviews: