CTC Union GW-732FW User Manual Download Page 75

Page: 75 / 86

Dual Band Wireless VoIP Gateway

User’s Manual

2-6-4 Backup / Restore

Backup Configurations File

System settings

→

Backup and Restore

The current system settings can be saved as a file onto the local hard drive. Click the

Backup Settings

button to save your current settings to a file.

Configuration File:

It is to backup the all settings.

Wireless Configuration File

：

It is to backup the Wireless settings.

Configuration Template File:

It is to backup the settings as template file for editing.

Restore Default Settings

System settings

→

Backup and Restore

You can backup settings to a file and restore settings from that file. You also can restore all settings back to
default by selecting

Restore Default Configurations

and click

Restore

Note: You have to save settings and restart, and all settings will take effect.

Summary of Contents for GW-732FW























































































Search results

Summary of Contents for GW-732FW

Reviews:

Related manuals for GW-732FW

Brands by name

Popular brands

CTC Union GW-732FW, User Manual

Search results

Summary of Contents for GW-732FW

Reviews:

Related manuals for GW-732FW

Brands by name

Popular brands