CTC Union GW-732FW User Manual Download Page 47

Page: 47 / 86

Dual Band Wireless VoIP Gateway

User’s Manual

WPA Cipher Suite:

WPA Cipher Suite is used for the configuration of WPA or WPA2 Mixed.

TKIP -

TKIP is the security protocol used in WPA. The length of TKIP encryption is longer than WEP

encryption that increases the complexity of decoding for crackers.

AES -

The most powerful encryption algorithm that is commonly used in WPA.

WPA2 Cipher Suite:

WPA2 Cipher Suite is used for the configuration of WPA2 or WPA2 Mixed.

TKIP -

TKIP is the security protocol used in WPA. The length of TKIP encryption is longer than WEP

encryption that increases the complexity of decoding for crackers.

AES -

The most powerful encryption algorithm that is commonly used in WPA.

Pre-Shared Key Format:

Select the Format of Pre-Shared Key. You can select Passphrase or Hex (64

characters) by entering a character string ranging from

“A-Z” and “0-9”.

Pre-Shared Key:

Enter a key of 8-64 characters long in the Pre-Shared Key filed. Make sure this key is

exactly the same on all other wireless stations.

Summary of Contents for GW-732FW























































































Search results

Summary of Contents for GW-732FW

Reviews:

Related manuals for GW-732FW

Brands by name

Popular brands

CTC Union GW-732FW, User Manual

Search results

Summary of Contents for GW-732FW

Reviews:

Related manuals for GW-732FW

Brands by name

Popular brands