background image

 

15 

15. INSTALLING THE SKIMMER (SK) 

 

 

Once the water of the swimming pool is +/- 5 cm under the skimmer hole, mark 

the hole in the liner with a felt pen and cut the skimmer’s square with a sharp blade the 
piece of marked square of liner (fig. 36). 
   

 

 

Cover the “Fitting Thread” with Teflon and screw tightly the connecting screw 

to the skimmer’s body. It’s important to put Teflon on all the connection threads to 
ensure a good seal. 

The excess of Teflon can be broken off. 

 
To put the skimmer on, start by placing the rubber gaskets one on each side (fig. 
37). Put the frame on the inside of the pool and insert a screw in the top central 
hole in order to go through the 

frame + rubber  liner + the other rubber 

skimmer’s body

, from the inside to the outside. Screw a little bit to hold it 

to the skimmer’s body (Figs. 38 & 39). 
 
Repetir esta operación en el agujero del marco central inferior, enroscar suavemente, 
a  continuación  ir  colocando  los  demás  tornillos  uno  después  de  otro,  siguiendo  el 
orden indicado, al final apretarlos firmemente.

 

 

 

   
 

 
 

Connect the end of the hose to the connection thread with a clamp. Fit the other end of 
the hose to the inlet of the filter equipment and tighten with the help of a clamp. 
 
 

Finally, place the basket inside the skimmer 

and close the skimmer’s body with the cover. 
 

 

To finish, fill the pool a little more than half of 

the skimmer’s gate to get water inside and fill the 
filter system.  
 
 

 

16. MAINTENANCE OF THE WOOD 

To keep the wood all the properties that have been applied in the manufacturing process (Autoclave and organic 
solvent), we suggest you to use a brush to apply water varnish in order to protect the wood from the weather 
changes (not included in the kit). 
We recommend to repeat the process at least once a year, to extend the life and improve the appearance of the 
wood. 

 
17. MAINTENANCE OF THE SWIMMING POOL 
 

- WATER MAINTENANCE 
 
All swimming pools need chemical treatment to maintain the water disinfected and crystal clear. Consult your chemical 
products supplier to determine those that are best for your needs. Water treatment procedure is not the same in all regions, 
because it depends on the water quality in each region. 
 
WARNING: An incorrect 

treatment may cause water pollution that produces infections, poisonings and diseases. 

 

fig.36 

fig.37 

 

fig.38 

fig.39 

Summary of Contents for Barrica Series





















Reviews: