background image

INSTRUCTION MANUAL

MODEL 4117-14 Block Up/Downconverter

TABLE OF CONTENTS                                           PAGE

Warranty

2

1.0 General

3

1.1  Equipment Description

3

1.2  Technical Characteristics

4

2.0 Installation

6

2.1  Ethernet Interface Installation

7

  

2.1.1  Methods of Connection

 7 

  

2.1.2  Ethernet Configuration

7

         

2.1.3  Web Page M&C

9

  

2.1.4  SNMP Configuration

9

2.2  Up/Downconverter Outline Drawings

12

2.3  Physical Interface

13

2.4  Installation/Operation

14

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross Technologies, Inc. products are warranted against defective materials and 
workmanship for a period of one year after shipment to customer. Cross Technologies, 
Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s 
option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall 
not be liable for any special, indirect, or consequential damages.  This warranty does not 
cover parts or equipment which have been subject to misuse, negligence, or accident by the 
customer during use. All shipping costs for warranty repairs will be prepaid by the 
customer.  There are not other warranties, express or implied, except as stated herein.

C

ROSS 

T

ECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005  •  FAX (770) 886-7964  •  Toll Free 888-900-5588

WEB www.crosstechnologies.com  •  E-MAIL [email protected]

4117-14 Manual, Rev. J

 

             Page 2

    

                     03/27/17  

Summary of Contents for 4117-14
















Reviews: