background image

CRL ESK1/ESP1 - ELECTRIC STRIKE KEEPER FOR SINGLE DOORS

10

crlaurence.com   |   usalum.com

*

THIS IS REQUIRED ONLY IF:

  1.  Electric Strike is replaced.
  2.  The latch sensor gives a false reading when the door is pushed out while secured.

To Adjust: 

  A)  Remove the      (2) 5/16-18 x 3/4" SHCS. 
  B)  Remove the Strike from the header.

 (Fig.10)

 

  C)  Loosen the      (2) 1/4"-20 x 1/2" SHCS. 
  D)  Apply pressure to the Strike Keeper to create a gap. 

(Fig.11)

 

  E)  Insert the 

ESP040

 Electric Offset Jig while holding the Strike Keeper. 

(Fig.12)

  F)  Push and hold the Strike Keeper in against the Jig and re-tighten the  
   

      (2) 1/4"-20 x 1/2" SHCS. 

(Fig.13)

  G)  Remove the 

ESP040 

Electric Offset Jig. 

(Fig.14)

 

  H)  Install the Electric Strike Assembly using the       (2) 5/16-18 x 3/4" SHCS. 

C

C

A

A

FIG. 14

FIG. 13

FIG. 11

FIG. 12

Strike 

Keeper

ESP040  

Electric  

Offset Jig 

ordered 

separately.  

Used only 

for the ESP 

Strikes

Strike 

Keeper

(2) 1/4"-20 x 1/2" 

SHCS

Strike 

Keeper

FIG. 10

(2) 5/16"-18 x 3/4" 

SHCS

C

(2) 1/4"-20 x 1/2" 

SHCS

Strike 

Keeper

C

A

ESP040  

Electric  

Offset Jig 

ordered 

separately.  

Used only 

for the ESP 

Strikes

ESP040  

Electric  

Offset Jig 

ordered 

separately.  

Used only 

for the ESP 

Strikes

ELECTRIC STRIKE ATTACHMENT (CONTINUED)

ELECTRIC STRIKE ADJUSTMENT

Summary of Contents for ESK1












Reviews: