background image

CRL ESK1/ESP1 - ELECTRIC STRIKE KEEPER FOR SINGLE DOORS

02

crlaurence.com   |   usalum.com

ORDER OF ASSEMBLY AND INSTALLATION

INTRODUCTION/TOOLS REQUIRED ............................................................................................................. 03

PARTS IDENTIFICATION.................................................................................................................................. 04

HEADER PREPARATION 

05 - 06

ELECTRIC STRIKE APPLICATIONS ................................................................................................................ 07

ESK1/ESP1 ELECTRIC STRIKE INSTALLATION 

08 - 11

  VOLTAGE AND WIRING .............................................................................................................................. 08

  ELECTRIC STRIKE ATTACHMENT ............................................................................................................ 09

  ELECTRIC STRIKE ADJUSTMENT ............................................................................................................ 10 

  RE-ATTACH STRIKE COVER AND MAKE FINAL ADJUSTMENTS .......................................................... 11

The rapidly changing technology within the architectural aluminum products industry demands that C.R. Laurence/U.S. Aluminum  

reserve the right to revise, discontinue, or change any product line, specification, or electronic media without prior written notice.

NOTE:

  Dimensions in parentheses (  ) are millimeters unless otherwise noted.

Summary of Contents for ESK1












Reviews: