8
CRISTÓFOLI
A U T O C L
A V E S
I N S T R U C T I O N M A N U A L
Table 1
The electrical installation must follow the data from table below.
Quadra 54 - 220 V
8,2 A
220 V AC » 198 V - 242 V
For distance up to 5 m (16 ft) from the
circuit breaker to the outlet used to
connect the equipment, use 2,5 mm wiring.
From 5 to 15 m (16 to 46 ft) use 4 mm,
and from 15 to 50 m (46 to 164 ft) 6 mm.
1 Breaker15 A.
MODEL
NOMINAL
CURRENT
WIRING GAUGE
CIRCUIT BREAKER
VOLTAGE
INSTALLATION INSTRUCTIONS
ELECTRICAL INSTALLATION
ou are going to install it. To do that, simply
Check if the voltage of the autoclave is the same of the place where y
look at the identification label in the back of the autoclave. See “
How to Identify your Autoclave
” (Fig. 14, page 18).
For the installation use a grounded, three-pin outlet (2P + G, 20A) connecting phase/neutral or phase/phase on the
side pins and grounding on the central pin (Fig. 2, page 9).
Never connect grounding to neutral
.
ATTENTION!
As in any other electrical device, grounding is very important for the safety of the operator and the warranty
of your equipment. Therefore,
never
remove or cut the plug’s central (grounding) pin off.
Non-compliance with this
requirement may damage your autoclave
.
Cristófoli is not responsible for damages caused by inadequate
installations and/or voltage
.
Never
use extensions, voltage transformers or any kind of adapters (Fig. 3, page 9).
For the proper functioning of your autoclave, the electrical voltage must be stable, in other words, without
oscillations Consult a professional electrician to check the electrical wiring in your building/workplace and make
.
sure they are according to the specifications required
It is mandatory the use of an exclusive circuit breaker for
.
the outlet where you intend to install your autoclave
. If after following all the specifications, the electrical current is
still oscillating, contact your local electricity company for repairs.
The equipment must be always carried by three or four people to prevent it from falling or causing an accident. The
storage/installation must be done in a place protected from the weather action (indoors) in normal temperature conditions
on a counter that can bear the weight of the autoclave.
Although simple, the installation of the Autoclave Cristófoli Quadra 54 must be performed by an authorized Cristófoli’s
technician, who will check whether the wiring and voltage of your building are in accordance with the required
specifications in this manual,
failure to observe this recommendation will cause immediate warranty cancellation
. In
order to have your equipment installed, please contact your local dealer. See also “
Warrant Terms
” (Page 25) and “
How to
Proceed When Service is Needed
” (Page 24).
PHYSICAL INSTALLATION
Install the autoclave on a flat, leveled and firm surface at a proper height for the operator to handle it
(approximately 80 cm / 2.6 feet from the ground)
(72,5 kg),
on a counter that can support the weight of the equipment
as well as its dimensions (54 x 54 x 75 cm - W x H x D). Leave enough room close to the autoclave for the proper
handling of the materials to be sterilized Install the autoclave in a ventilated and clean place, apart from the room
.
where the patients are treated. The ideal place for the installation of the autoclave should be a separate sterilization
room
Important!
Install your autoclave where it can be easily unplugged.
.
Note:
In areas where voltage is 220V:
PP (Phase-Phase) use a “bipolar” breaker
PN (Phase-Neutral) use a “unipolar” breaker connected to Phase.
1
2
4
3
Summary of Contents for Autoclave Quadra 54
Page 2: ......
