Page 22
Feature #1
Transmitter Programming Mode
The first level in the programmable features menu is Transmitter Pro-
gramming Mode, by which additional or replacement transmitters can be
programmed to operate the system. It is important to note that when a
transmitter is programmed into the system, the ATV Warning is activated
and all previous transmitter codes in the system’s memory are deleted.
If a third or fourth transmitter is to be added to operate the system, all of
the transmitters must be programmed into system's memory at the same time,
as the first new transmitter code entered will erase the existing transmitter
codes. Therefore, if your system should ever be compromised by the
addition of an unauthorized transmitter, the ATV feature will warn you. By
simply reprogramming all of your transmitters into the system, the
unauthorized transmitter will be erased.
To program a transmitter:
Follow Steps 1 to 4 on page 20; at Step 4 the Valet Switch will be pressed
and released one time only. The system’s response will be one siren chirp,
and the Status Light flashing one time, pausing, then repeating. Within 10
seconds, press and release the Large Upper Button of the first transmitter.
The system confirms “learning” the transmitter’s code chirping the siren
once. Repeat this action with each transmitter to be programmed. Only the
Large Upper Button of the transmitter needs pressing and release; all of the
other transmitter button’s operations will be learned automatically.
To program a transmitter to a “2nd” or “3rd” system:
Up to three Crime Guard systems may be independently operated using
a single transmitter. To accomplish this, the transmitter’s button functions
are different for each of the vehicles. This prevents Arming or Disarming the
multiple systems simultaneously when all are within range of the transmitter.
To program a transmitter for 2nd or 3rd systems, when programming press
and release either of the small buttons instead of the Large Upper Button. The
system will automatically assign the transmitter’s other functions in a
different order. The following chart shows button function assignment.
THE 328i
3
’s PROGRAMMABLE FEATURES
Arm/Disarm Auxiliary Output
Large Button
Small Button
Small Button
Large Button
Small Button
Large Button
Only the “Arm/Disarm” button is pressed when programming.
Page 23
Feature #2
SecureCode Programming Mode
(Factory Default Setting: 1 Press)
SecureCode is a unique patented feature which allows you to custom
select the number of Valet Switch presses which would be required in order
to perform an Emergency Override. Instead of “1 press” of the Valet Switch,
a customized programming of the SecureCode would require from 2 to 12
presses. If any of the three Vehicle Recovery features are utilized, a
customized SecureCode would require that the correct SecurCode entry of
Valet Switch be made to cancel the Vehicle Recovery activation.
The “as received” factory default setting of “1 press” is the most
convenient, as an Emergency Override will occur instantly when the Valet
Switch is pressed, but it is not as secure as a customized setting. When a
customized SecureCode has been programmed, the system will disarm a few
seconds after the correct entry.
To custom program a new SecureCode:
Follow Steps 1 to 4 on page 20; at Step 4 the Valet Switch will be pressed
and released two times. The system’s response will be two siren chirps, and
the Status Light flashing twice, pausing, then repeating. Within 10 seconds,
press and release the transmitter’s Large Upper Button; the siren will chirp
twice to confirm system is ready to accept the new SecurCode entry. Now
press and release the Valet Switch the desired number of times. The
SecureCode can be programmed for 1 to 12 presses, but the entry must be
made within 5 seconds. Wait for the siren to chirp the same number of times
as the Valet Switch presses to confirm the new SecureCode entry.
Important:
If no additional features need to be programmed, exit Programming
Mode by allowing the 10 second time limit to expire without any further
programming activity. Do not exit Programming Mode by turning on the
ignition switch.
Feature #3
Chirp Confirmation
(Factory Default Setting On)
This feature allows the permanent removal of the system’s chirping the
siren as a audible confirmation when performing functions such as Arming
and Disarming. Please note that utilizing this feature to remove the
confirmation chirps does not affect siren chirping operations associated
with the ATV Warning, sensor prewarning or Programming Mode.
