manualshive.com logo in svg

Crestron Cameo C2N-CBF, Operations & Installation Manual

Share
Download
Crestron Cameo C2N-CBF Operations & Installation Manual Download Page 5

Crestron 

C2N/C2NI-CB Series

 Cameo

™

 Keypads

 

Cameo

™

 Keypads: C2N/C2NI-CB 

Series 

Introduction 

Features and Functions 

The Crestron

®

 C2N/C2NI-CB Series Cameo keypads are a new 

generation of wall-mounted user interfaces that can be part of any 
Crestron total solution control system network (Cresnet

®

). The keypads 

are available in three versions: C2N-CBF, Flush Mount (no back box 
required) for domestic and international installation; C2N-CBD, Standard 
Mount (Decora

®

 style), back box installation, for domestic installation; 

and C2NI-CBUK, Standard Mount, optional UK-style back box, for UK 
installation. 

For maximum flexibility in all configurations, a complete set of button 
caps and spacers in three sizes is included with every keypad. The 
installer can customize and configure up to six backlit caps, for “rocker” 
left/right action, single press operation, or press and hold mode—up to 18 
functions in total.  

Functional Summary 

 

 

 

 

 

 

 

 

• 

Six switches, each programmable for left/right “rocker” action, 
single press operation, or press/hold mode, enabling up to 18 
functions  

• 

Button caps and spacers supplied in single-, two-, and three-
button configurations—any combination may be used  

• 

LED feedback and switch backlighting intensity are 
individually programmable 

• 

Exclusive flush-mount, Decorator style, or traditional mounting 
installation 

Operations & Installation Guide - DOC. 6346A 

Cameo™ Keypads: C2N/C2NI-CB Series  

•

  1 

Summary of Contents for Cameo C2N-CBF

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands