manualshive.com logo in svg

Crestron Cameo C2N-CBF, Operations & Installation Manual

Share
Download
Crestron Cameo C2N-CBF Operations & Installation Manual Download Page 16

Cameo

™

 Keypads 

Crestron 

C2N/C2NI-CB Series 

Network Device Tree – Sub-Menu  

 

5.  Enter a new Net ID and press 

Enter

.  

Enter New Net ID 

 

6.  Repeat this procedure for each additional network device 

requiring a Net ID change. 

Assembly and Installation 

Assembly of the keypad consists of placing the button caps/spacers in 
position based on how the unit is programmed, securing them together 
with a plastic button support, putting the button cap/spacer assembly in 
place on the rear housing and switch assembly, and attaching the bezel.  

The button caps are tapered, and are often installed in a shingle-style 
pattern (refer to the “

Keypad Physical Views

” illustration on page 4). 

Usual orientation of the keypad is with the LEDs on the left. It can, 
however, be inverted with the LEDs on the right, but the original 
relationship of the button numbers to the LEDs remains, i.e., with the unit 
inverted, row one is on the bottom – row six is on the top, and 
programming of the switches would have to be done accordingly. 

12  

•

  Cameo™ Keypads: C2N/C2NI-CB Series 

Operations & Installation Guide - DOC. 6346A 

Summary of Contents for Cameo C2N-CBF

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands