manualshive.com logo in svg

Crestron Cameo C2N-CBF, Operations & Installation Manual

Share
Download
Crestron Cameo C2N-CBF Operations & Installation Manual Download Page 32

Cameo

™

 Keypads 

Crestron 

C2N/C2NI-CB Series 

Cameo Keypad Button and Feedback LED Arrangement 

 

In cases where it is desirable to mount the keypad with the feedback 
LEDs on the right, programmers will have to take into account that 
physically, button 6 is now at the top, button 1 is at the bottom, and that 
the right and left switch positions are reversed. Bear in mind, however, 
that when combining buttons in this orientation, the usual programming 
constraints still apply. For example, if merging buttons 4, 5, and 6, even 
though button 6 is now physically at the top of the keypad, button 4 still 
controls the mode of the merged buttons. 

NOTE:

 A Crestron module in Crestron Database version 17.1.0, the 

C2N-Cameo Bargraph Feedback v1.0, makes it possible to use the 
feedback LEDs like a bargraph, so that for a function like volume 
control, as the switches are used to control the volume, the LEDs display 
its approximate level. 

Example Program 

An example program for the Cameo keypad is available from the 
“Example Program” section of the Crestron website 
(

http://www.crestron.com/exampleprograms

). Search for C2N-CB 

Example Program (ZIP). 

28  

•

  Cameo™ Keypads: C2N/C2NI-CB Series 

Operations & Installation Guide - DOC. 6346A 

Summary of Contents for Cameo C2N-CBF

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands