background image

Title part xxx

Subtitle part xxx

39

craftsman marine diesel engines CM4.33 / cm4.42

Problem

Probable cause

Solution

10. 
Excessive fuel consump-
tion of engine

•  Poor or polluted fuel quality 

•  Defective injector / injection pump

•  Incorrect injection moment

•  Excessive wear and tear of cylinder / piston

•  Insufficient supply of combustion air

•  Check fuel quality. Drain fuel tank and rinse it 

      well. Fill with good quality fuel

•  Check and replace if necessary 

•  Check / adjust

•  Check compression, overhaul engine if neces-

     sary

•  Check the air intake and the ventilation ope

     nings in the engine room

11. 

Blue smoke coming out of 
the exhaust (when idling)

•  Oil level too high

•  Excessive inclination  angle of the engine

•  Leaking  oil seal of the turbo compressor

•  Lower oil level

•  Check / adjust alignment of engine 

•  Check / replace

12. 

Black smoke coming out of 
the exhaust (under load)

 

• 

 Defecte turbocompressor

• 

•  Insuffient supply of combustion air

•  Leakage in air intake manifold

•  Defective injector / injection pump

•  Incorrect injection moment

•  Incorrect valve clearance

•  Excessive wear and tear of cylinder / piston

•  Engine overheated, does not reach maximum rpm

• 

Check air intake as well as the ventilation 

openings in the engine room

• 

Check/ replace

• 

Check/ replace

• 

Check and replace when necessary

• 

Check/readjust

• 

Readjust

• 

Check compression, overhaul the engine if needed.

• 

Check the dimensions (diameter and pitch) 

of the propeller and replace the propeller if 

necessary.

13. 

Engine produces white 
smoke from the exhaust 
(at full load) 

•  Air inclusion in the fuel system

•  Defective injector / injection pump

•  Water in the  fuel system

•  Defective pre-heating plugs 

•  Incorrect valve clearance

•  Incorrect injection moment

•  Poor fuel quality or polluted fuel

•  Condensation of vapour in the exhaust system, on account of very low 

     ambient temperature

•  Check / bleed the system

•  Check  / replace if necessary

•  Check / replace water separator / fuel filter

•  Check / replace

•  Check / adjust

•  Check / adjust 

•  Check fuel quality. Drain fuel tank and rinse it

      well. Fill with good quality fuel

•  No problem, no danger

Problems and solutions   14

Summary of Contents for CM4.33

















































Reviews: