Craftsman CM4.33 Manual Download Page 23 | Manualshive

Page: 23 / 48

background image

Title part xxx

Subtitle part xxx

23

craftsman marine diesel engines CM4.33 / cm4.42

Checking of the cooling water strainer

Each day, prior to starting the engine, make sure that the

cooling water strainer is not clogged by dirt. Close the

raw water seacock and remove the cover from the filter

housing for proper inspection.

Cleaning of the cooling water strainer

Clean the filter element at least twice a year, or whene-

ver necessary. If the cooling water strainer gets clogged

up, the cooling liquid in the engine may overheat.

When closing the strainer gain, make sure that the cover

is perfectly shutting the unit off. If and when air is suc-

ked into the system, on account of a badly closing filter

cover, there is a severe risk of overheating of the engine.

Again: make absolutely sure that the cover fits the strai-

ner housing well and without any air leaks!

Cooling water strainer

Maintenance and inspection 11

«
...
21
22
23
24
25
...
»

Summary of Contents for CM4.33

















































Reviews:

No comments

Related manuals for CM4.33

Brand: Beta Marine Pages: 88

Brand: PCM Pages: 83

HYDRO-FORCE 65043

Brand: Bestway Pages: 8

Brand: BMW Pages: 41

Brand: Volvo Penta Pages: 96

Brand: Volvo Penta Pages: 106

Brand: Lycoming Pages: 568

SKALAR SC Series

Brand: Hacker Pages: 2

Brand: Homa Pages: 34

Brand: Yanmar Pages: 2

Brand: Yanmar Pages: 2

Brand: Yanmar Pages: 48

Brand: Kingfisher Pages: 10

MAX-37SZ-H RING

Brand: O.S. engine Pages: 4

Brand: O.S. engine Pages: 17

Brand: O.S. engine Pages: 22

MAX-12TR Series

Brand: O.S. engine Pages: 30

Brand: O.S. engine Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands