Craftsman CM4.33 Manual Download Page 29 | Manualshive

Page: 29 / 48

background image

Title part xxx

Subtitle part xxx

29

craftsman marine diesel engines CM4.33 / cm4.42

Remove the fuel filter

Close-off the fuel supply to the engine. Remove the en-

tire filter with the aid of a special tool. It is possible that

the filter still contains some fuel, which please collect

and treat it in accordance with the environmental direc-

tives in your country.

Do not smoke when working at or around

the fuel system and avoid open fire.

Fit the fuel filter

Clean the surface to touch the engine before fitting the

filter. Grease the rubber ring with clean engine oil. Fill

the filter with clean diesel fuel. Position the filter against

the filter housing and tighten it with one half to three

quarters of a turn.

Clean the filter of the fuel lift pump and reopen the cock

of the fuel supply.

Cleaning the filter of the fuel lift pump

Consult your dealer.

Fuel filter

Maintenance and inspection 11

«
...
27
28
29
30
31
...
»

Summary of Contents for CM4.33

















































Reviews:

No comments

Related manuals for CM4.33

Brand: DAF Pages: 87

Vanguard EFI 380000

Brand: Briggs & Stratton Pages: 100

Brand: Leb Electronics Pages: 24

Brand: Jiecang Pages: 2

Brand: Vimar Pages: 16

Brand: MTU Pages: 187

Brand: O.S. engine Pages: 18

Revenge CTM Series

Brand: Absima Pages: 3

Featherweight 45

Brand: Seagull Pages: 25

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brand: Honda Pages: 5

Brand: Honda Pages: 60

Brand: Rockwell Automation Pages: 28

Brand: Stiga Pages: 51

Brand: Power smart Pages: 28

Brand: Hirth Pages: 28

Brand: Nanni Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands