background image

Safety Instructions

IMPORTANT SAFEGUARDS

1.  Place the assembled unit on a suitable firm, flat and substantial work surface, at a height that is comfortable for easy operation.
2.  Always locate the unit away from the edge of a work surface.
3.  Always disconnect the CraftDragon® ImPress from the main supply when not in use and when cleaning.
4.  Do not lock down the ImPress whilst the heated Imp unit is still hot.
5.  Do not leave the CraftDragon® ImPress on unattended.
6.  Never cover the CraftDragon® ImPress when switched on or hot as this may lead to a risk of fire.
7.  Make sure that when using the CraftDragon® ImPress for hot foiling the unit is away from flammable or perishable materials.
8.  Position the mains lead so that it does not get in your way when using the CraftDragon® ImPress and make sure that the power cable cannot

be damaged by the heated area of the CraftDragon® ImPress.

9.  Before use, always place the ImPress unit on a solid, stable surface to avoid tipping or dropping it.

10.  Do not touch hot areas of the CraftDragon® ImPress with bare hands when switched on.
11.  Use a heat resistant glove or pad when removing dies etc.
12.  Keep heated surface away from all personal body parts, animals or children.
13.  The CraftDragon® ImPress will become very hot during use.
14.  Close supervision is required when the CraftDragon® ImPress is used near or by children.
15.  Never allow the cord to touch wet or hot surfaces, become twisted or be within the reach of children or animals.
16.  Do not place on or near a hot gas or electric burner.
17.  Do not use out of doors, unless under safe conditions.
18.  Never use the CraftDragon® ImPress with a damaged cord or plug or after the CraftDragon® ImPress has malfunctioned or been damaged

in any other way.

19.  Never attempt to open any part or dismantle the controls of the CraftDragon® ImPress. Responsibility for failure cannot be accepted if these

instructions have been ignored.

20.  Do not use the CraftDragon® ImPress for anything other than the intended uses.
21.  Only use the heated Imp unit when fixed in the press.
22.  Do not remove the locking handles from the press unit.
23.  Only use heated unit on recommended materials.
24.  This appliance is intended for household, supervised educational or office use only.
25.  Do not use the CraftDragon® ImPress in the immediate surroundings of a bath, a shower or a swimming pool.

© CraftDragon

®

3

Summary of Contents for CD-ES 080902


















Reviews: