Craden DP6 Specifications Download Page 42 | Manualshive

Page: 42 / 62

background image

42

5.4.17 DP7 Carriage Lift Button

The carriage lift button raises the carriage at its right home position so that envelopes and other wide
documents may be fed without the carriage weight pressing on them.
1. Remove the ribbon shield by raising the carriage, pushing down on the shield until it snaps free from the

carriage and sliding it out to the right.

2. Move the carriage to the position on the right side of the printer where the carriage is lifted to its highest

point by the lift button.

3. The gap between the printwires and the platen should now be between 0.026” and 0.030”.
4. To adjust, slightly loosen the right front wheel guide clamp screw and raise or lower the wheel guide to get

the proper print gap. Tighten the screw while holding the wheel guide.

5. Reheck the gap and repeat step 4 if necessary.

Wheel guide locking
screws

Carriage lift
cam 67296

Carriage lift
button 67334

«
...
40
41
42
43
44
...
»

Summary of Contents for DP6































































Reviews:

No comments

Related manuals for DP6

imagePROGRAF iPF760

Brand: Canon Pages: 12

imagePROGRAF iPF825 MFP Basic Guide No.1

Brand: Canon Pages: 16

imagePRESS C850

Brand: Canon Pages: 146

imagePRESS C850

Brand: Canon Pages: 63

imagePROGRAF iPF760

Brand: Canon Pages: 132

imagePROGRAF iPF825 MFP Basic Guide No.1

Brand: Canon Pages: 8

imagePROGRAF TX-2000

Brand: Canon Pages: 14

i-SENSYS MF6180dw

Brand: Canon Pages: 1040

imagePROGRAF iPF815

Brand: Canon Pages: 48

imageRUNNER 1025

Brand: Canon Pages: 6

imageRUNNER 2230

Brand: Canon Pages: 6

IMAGEPRESS C7010VPS

Brand: Canon Pages: 388

Brand: Canon Pages: 56

imagePROGRAF iPF8300

Brand: Canon Pages: 24

imagePROGRAF iPF8300

Brand: Canon Pages: 4

imagePROGRAF iPF6350

Brand: Canon Pages: 12

imagePROGRAF iPF6350

Brand: Canon Pages: 2

imageCLASS MF8380Cdw

Brand: Canon Pages: 192

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands