background image

EN-1

Kendall SCD 700 Series

Indications

The Kendall SCD 700 Sequential Compression System (hereby referenced as “Kendall SCD 700 Series”) is designed to 

apply intermittent pneumatic compression to increase venous blood flow in at-risk patients in order to help prevent 

deep vein thrombosis and pulmonary embolism.  The System consists of the controller, the tubing sets (provided 

with the controller) and single-patient use garments (purchased separately from this controller).  The garments, both 

leg sleeves and foot cuffs, compress the limbs to enhance venous blood movement. After the compression cycle has 

reached set pressure, the Controller measures the time it takes for the limbs to refill with blood and waits that period 

of time before the next compression is initiated. 

Leg Compression

The use of the Kendall SCD 700 Series Compression System with Leg Sleeves is indicated for: 

  1.  Deep vein thrombosis and pulmonary embolism prophylaxis. 

Foot Compression

The use of the Kendall SCD 700 Series Compression System with Foot Cuffs is indicated for: 

  1.  Circulation enhancement.
  2.  Deep vein thrombosis prophylaxis.
  3.  Edema - Acute.

4.  Edema - Chronic.

  5.  Extremity pain incident to trauma or surgery.

6.  Leg Ulcers.

  7.  Venous stasis / venous insufficiency.

If you need further information regarding the Kendall SCD 700 Series Compression System or its clinical benefits, 

please contact your  Covidien Sales Representative. 

Contraindications

Leg Compression 

The Kendall SCD 700 Series Compression System may not be recommended for use with Leg Sleeve on patients with 

the following: 

  1. Any local leg condition in which the sleeves may interfere,  such as: (a) dermatitis, (b) vein ligation [immediate 

postoperative], (c) gangrene, or (d) recent skin graft. 

  2. Severe arteriosclerosis or other ischemic vascular disease. 
  3. Massive edema of the legs or pulmonary edema from congestive heart failure. 
  4. Extreme deformity of the leg. 
  5. Suspected pre-existing deep venous thrombosis. 

Foot Compression

The Kendall SCD 700 Series Compression System may not be recommended for use with Foot Cuffs on patients with 

the following: 

  1. Conditions where an increase of fluid to the heart may be detrimental. 
  2. Congestive heart failure. 
  3. Pre-existing deep vein thrombosis, thrombophlebitis or pulmonary embolism. 

Use with caution on the infected or insensitive extremity.

Summary of Contents for Kendall SCD 700 Series


































Reviews: