Cornelius R-454C Page 97 Manual Download

Page: 97 / 111

Viper Installation, Service & Decommissioning Manual

Publication Number: 620073146SER

- 94 -

ONDENSER

OTOR

EPLACEMENT

The fan motor is located on the top of the unit, as shown in Figure 76. If the motor needs replacement, perform the proce-
dure in Table 79 to remove and reinstall a motor.

Figure 76. Condenser Fan Mounting Nuts

In Step 1

, disconnect electrical power from the unit. Failure to disconnect the power could result in serious injury, death, or

equipment damage.

OMPRESSOR

EPLACEMENT

Caution should be used when working with refrigerants. To replace a compressor, perform the procedure in Table 80.

Be sure to reclaim refrigerant when replacing compressor.

n Step 1, disconnect electrical power from the unit. Failure to disconnect the power could result in serious injury, death, or

equipment damage.

Table 79.

Step

Action

Disconnect electrical power from the unit.

Disconnect the fan by unplugging the connector.

Remove the four locking nuts securing the fan to the top of the condenser.

Lift the fan and shroud off the unit.

Remove the four screws and washers securing the fan to the shroud.

Replace the fan.

Reverse the procedure to install the new fan.

Reconnect power to the unit.

Table 80.

Step

Action

Disconnect power to the unit.

Remove the rear cover and side panels.

Label and disconnect all wires from the compressor.

Remove the four (4) mounting nuts from the base of the compressor.

Remove all insulation from around fittings.

Unsweat the suction line from the compressor.

Locking

Nuts

Locking

Nuts

WARNING:

Summary of Contents for R-454C
















































































































Search results

Summary of Contents for R-454C

Reviews:

Related manuals for R-454C

Brands by name

Popular brands

Cornelius R-454C, Manual

Search results

Summary of Contents for R-454C

Reviews:

Related manuals for R-454C

Brands by name

Popular brands