background image

StripPoint User Manual  rev.1_0 

20 

 

 

 

• Increase the separation between the equipment and receiver. 
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
• Consult the dealer or an experienced radio/TV technician for help. 
 

RF Exposure Warning for North America, and Australia 

Warning

! To meet FCC and other national safety guidelines for RF exposure, 

the antennas for this device must 

be installed to ensure a minimum separation distance of 20cm (7.9 in.) from persons

 
 

WEEE & RoHS Statement 

 
 

The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that 
products must not be disposed of the normal unsorted municipal waste stream. Appliances must be collected 
separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact 
on human health and the environment. 
 
The consumer must contact their local authority or retailer for information concerning disposal of their 
products. 
 
CORE Lighting provides a take-back facility for batteries used within CORE Lighting products, although the 
expense for transport remains the liability of the consumer. Please contact CORE Lighting directly if this service 
is required. 
 
 

 

Summary of Contents for StripPoint
























Reviews: