Coram Showers PREMIER Manual Download Page 2

Page: 2 / 16

1500 RAIL - PN80599
1700 RAIL - PN80600

PN11029

1500 RAIL - PN80599
1700 RAIL - PN80600

Drill holes in both wall channels at the points shown (in the groove) using a 4.5mm drill bit.

Ensure the shower tray is level in all directions.

IMPORTANT:

Clean the tray and seal the gap between the tray surface and tiles. It is important that the tray is sealed right up to

the tray edge so that the bottom of the wall channel is sealed. Failure to do this will cause water to leak under the wall channel
and between the tray and tiles, resulting in damp patches on the wall and under the tray.

PN11031

100mm

max

100mm

max

ø 4.5

1500 =

PN40272

1700 =

PN40273

Check contents of pack before installation. If anything is
missing, contact our Customer Careline for assistance.

CUSTOMER CARELINE: 01746 713410

PN3230

PN3225

32mm

PN4745

PN60093

12mm

PN60220

PN40309

PN40311

PN40308

PN60162

PN50359

PN50370

PN80618

PN60014

13mm

PN3222

10mm

Summary of Contents for PREMIER

















Search results

Summary of Contents for PREMIER

Reviews:

Related manuals for PREMIER

Brands by name

Popular brands

Coram Showers PREMIER, Manual

Search results

Summary of Contents for PREMIER

Reviews:

Related manuals for PREMIER

Brands by name

Popular brands