background image

9

Push fit 'flipper seals' (PN40309) onto the back edge of the doors. 

Ensure the flipper seal 'flaps' are on the outside of the doors. 

Push fit 'magnetic seals' (PN40311) onto the closing edge of the 
doors (the same side as door handle holes). 

Note:

 Ensure the magnetic seals are positioned as shown.

Note: 

Wetting the glass with water will help fit the seals.

PN 
40309

Outside  

face of  

door

Door  
handle  
holes

PN40309

PN40311

Door  

handle  

holes

Outside  

face of  

door

PN40311

PN40311

10mm

ø 3

mm

8

Fit 'flipper seals' (PN40308) onto the edge of the fixed 
panels. 

Ensure the flipper seal 'flaps' are on the 

inside. Note: 

Wetting the glass with water will help to 

fit the seals.
From inside the enclosure, place fixed panel retainer 
covers (PN80618) onto the top and bottom fixed 
panel brackets. Fix using the 12mm screws and fit the 
retainer caps (PN50370).

PN80618

Inside 

PN40308

PN50370

12mm

Fixed  
panel  
bracket

5

7

Check the door frame is vertical and is centrally positioned between the wall channels. 
From inside the enclosure, in the positions shown, drill through the wall channels into the fixed panels using a 3mm drill bit,  

do not drill too deep! 

Fix using 6 x 10mm screws.

From inside 

Summary of Contents for PREMIER

















Reviews: