2
english
Step 2
Step 3
Step 1
Dropout
18mm Screw
Rear View
Nut
Braze-on
Extender
10mm
Screw
Reflector
Bracket
Struts
Nut
WARNING!
Do not modify rack or bicycle. If rack will not
fit on your bicycle, consult your local dealer or call 1-800-
456-2355 for assistance. Periodically check all nuts and bolts
for tightness
Parts List:
6 – 10 mm Buttonhead Screws
2 – 25 mm Buttonhead Screws
8 – Nylock Nuts
2 – Extenders
2 – 1/2” Seat-Stay Clamps
2 – 9/16” Seat-Stay Clamps
1 – Reflector Bracket
1 – 3 mm Allen Wrench
Step 1
Attach extenders to rack
using four 10mm button
head screws and nylock
nuts. Do not tighten.
Note:
Extenders have an offset twist
and can be installed in wide
or narrow position to match
seat stay width.
Step 2
Remove rear quick release.
Spread rack struts to fit on the
outside of the dropouts. Install
extra long quick release
supplied with rack. Follow your
bicycle/wheel manufacturer
recommendations for
removing and installing quick
releases or have a qualified
bicycle shop replace it for
you.
Step 3
Attach extenders to the bike frame “Braze-on” mounts with
25mm buttonhead screws. Bend extenders (by hand or
with an adjustable wrench) to align with braze-on mounts.
!
INSTALLING EXPEDITION 1 RACK
10mm
Screw
Seat-Stay
Clamps for bikes
without (braze-ons)
Parts List:
2 – 18 mm Buttonhead Screws
6 – 10 mm Buttonhead Screws
2 – 25 mm Buttonhead Screws
8 – Nylock Nuts
2 – Extenders
2 – 1/2” Seat-Stay Clamps
2 – 9/16” Seat-Stay Clamps
1 – Reflector Bracket
1 – 3 mm Allen Wrench
Step 1
Attach extenders to rack
using four 10mm button
head screws and nylock
nuts. Do not tighten.
Note: Extenders have an offset twist
and can be installed in wide
or narrow position to match
seat stay width.
Step 2
Spread rack struts to fit on
the outside of bike frame.
Attach rack to frame using
18mm screws. Do not tighten.
Note: Some bikes may have
insufficient clearances
between the high gear
(smallest cog) of the rear
freewheel and the inside of
the dropout to permit
installation of the nylock nut.
In this case, install the hardware in the reverse order
with the nylock nut on the outside. You will need to
remove the rear wheel of the bike in order to install
the screw from the inside. The lower profile of the
screw head should provide sufficient clearance.
Step 3
Attach extenders to the bike frame “Braze-on”
mounts with 25mm buttonhead screws. Bend
extenders (by hand or with an adjustable wrench) to
align with braze-on mounts.
Note: For bicycles without seat stay “Braze-ons” use vinyl
coated Seat-Stay Clamps (2 sizes included). Attach
with 10mm screws and nylock nuts.
Step 4
Adjust rack until rack top is level with ground by
sliding it on extenders until level. Tighten all rack
screws & nuts.
Step 5
Install reflector bracket over rack and tighten with
reflector and reflector screw from your bicycle.
INSTALLING EXPEDITION 1 DISC RACK
Step 3 (Note)
10mm
Screw
Seat-Stay
Clamps for bikes
without (braze-ons)
Step 3 (Note)
25mm
Screw
Nut
Wide
Narrow
Step 1
Step 2
Quick
release
rod
Step 3
25mm
Screw
Nut
Wide
Narrow
10mm Screw
Reflector Bracket
Extender
Nut