Cooper & Hunter TERRA CH-S09FHCP Service Manual Download Page 44 | Manualshive

Page: 44 / 57

background image

Service diagnosis

4

2

Domestic air conditioner

10.3.11 Loss of synchronism detection

Inverter side current detection is abnormal

Outdoor Display LED1 flash 18 times
LED1 flash 19 times

Method of                The position of the compressor rotor can not detected normally
Malfunction
Detection

Malfunction            when the wiring of compressor is wrong or the connection is poor;
  Decision                or the compressor is damaged
Conditions

Supposed

Faulty The wiring of compressor

Causes

Faulty compressor

Faulty PCB

Troubleshooting * Caution Be sure to turn off power switch before connect or disconnect connector, or parts

damage may be occurred.

Within 3 minutes after the machine is

supplied with power and turned on with
the remote controller, check whether
the compressor can start up

1. The wiring of compressor is incorrect

or the connection is poor;

2. The compressor is damaged

At first, the compressor start up ,soon the

compressor stopped with the LED1 on the
outdoor PCB blinks

1Hz

19/18 times

IPM Module is damaged and needs

replacing.

the

Malfunctions

exist

also,

the

compressor is damaged replace a
new one

YES

NO

YES

Malfunction unsolved

Maybe there is some disturbance

«
...
42
43
44
45
46
...
»

Summary of Contents for TERRA CH-S09FHCP


























































Reviews:

No comments

Related manuals for TERRA CH-S09FHCP

Brand: Ideal Warehouse Pages: 32

Altherma EHVH04S23DAV

Brand: Daikin Pages: 12

Altherma EBLQ011CAV3

Brand: Daikin Pages: 140

Brand: Daikin Pages: 56

Brand: Daikin Pages: 38

Brand: Daikin Pages: 60

SUPER MULTI NX FTXS09LVJU

Brand: Daikin Pages: 14

Brand: Daikin Pages: 94

Altherma 3 R ECH2O

Brand: Daikin Pages: 68

Altherma EHVZ04S18CB

Brand: Daikin Pages: 92

Brand: Daikin Pages: 246

Altherma EHY2KOMB28AA

Brand: Daikin Pages: 28

Brand: Daikin Pages: 12

Brand: Daikin Pages: 92

Brand: Daikin Pages: 12

SkyAir FBQ18PVJU

Brand: Daikin Pages: 10

GWH09ACC-S6DBA1A/O

Brand: Gree Pages: 123

Brand: Hyundai Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands