Cooper & Hunter TERRA CH-S09FHCP Service Manual Download Page 33 | Manualshive

Page: 33 / 57

background image

Service diagnosis

3

1

Domestic air conditioner

10.3.3 Indoor AC fan motor malfunction

Indoor Display      E14

Method of              The rotation speed detected by the Hall IC during fan motor operation is used to determine
Malfunction            abnormal fan motor operation
Detection

Malfunction            when the detected rotation feedback signal dont received in 2 minutes
Decision
Conditions

Supposed                 Operation halt due to breaking of wire inside the fan motor.
Causes                     Fan motor overheat protection

Operation halt due to breaking of the fan motor lead wires
Detection error due to faulty indoor unit PCB

Troubleshooting * Caution Be sure to turn off power switch before connect or disconnect connector, or else

parts damage may be occurred.

Check whether terminals

on indoor pcb is well ?

Electrify the machine again and turn it on in the cooling operation,

Measure voltage between the positions 1and 3 of Terminal CN5

on the indoor PCB

the voltage is about 90-220vac

check whether motor can run

when turn on the unit

the indoor motor is damaged and need replace

Yes

Measure whether there is voltage pulse (0-5VDC)

between the positions middle wire and black wire

of Terminal CN2 on the indoor PCB

the indoor pcb is damaged and need replace

Pull out the terminals on the indoor

mainboard and reinsert them.

Is it ok?

«
...
31
32
33
34
35
...
»

Summary of Contents for TERRA CH-S09FHCP


























































Reviews:

No comments

Related manuals for TERRA CH-S09FHCP

Brand: Daewoo Pages: 14

Brand: DAEWOO ELECTRONICS Pages: 18

MagPurix 24 EVO

Brand: ZINEXTS Pages: 36

Brand: Gree Pages: 28

Brand: Airwell Pages: 55

Brand: Nortek Pages: 16

Brand: iCovir Pages: 24

CZF024 THRU 060

Brand: York Pages: 26

Brand: Argo Pages: 92

Brand: Ballu Pages: 46

Brand: Carrier Pages: 6

Brand: Parker Pages: 36

Brand: Aircommand Pages: 22

Brand: Refco Pages: 8

Brand: Coway Pages: 124

Multi-Tech 2000

Brand: Surround Air Pages: 8

Brand: Gree Pages: 125

ELFOFresh2 CPAN-U 70-120 Series

Brand: CLIVET Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands