Control Techniques Unidrive M200 Quick Start Manual Download Page 42

Page: 42 / 56

Unidrive M200/201 Control Quick Start Guide

Issue Number: 3

This parameter with

PID1 Output Lower Limit

(Pr

) allows the output to be limited to a range. For

further information, refer to the

Parameter Reference Guide.

See

PID1 Output Upper Limit

(Pr

Bit 0:

Stop on defined non-important trips

Bit 1:

Disable braking resistor overload detection

Bit 2

: Disable phase loss stop

Bit 3:

Disable braking resistor temperature monitoring

Bit 4:

Disable parameter freeze on trip. Refer to

Parameter Reference Guide.

Displays the maximum heavy duty current rating of the drive.

Displays the software version in the drive.

PID1 Output Upper Limit

Num

0.00 to 100.00 %

100.00 %

RFC-A

PID1 Output Lower Limit

Num

±100.00 %

-100.00 %

RFC-A

Action On Trip Detection

Num

0 - 31

RFC-A

Maximum Heavy Duty Rating

Num

0.00 to Drive HD Current Rating A

RFC-A

Software Version

Num

0 to 99.99.99

RFC-A

Summary of Contents for Unidrive M200

























































Search results

Summary of Contents for Unidrive M200

Reviews:

Brands by name

Popular brands

Control Techniques Unidrive M200, Quick Start Manual

Search results

Summary of Contents for Unidrive M200

Reviews:

Brands by name

Popular brands