manualshive.com logo in svg

Contrec 515, Operation Manual

Share
Download
Contrec 515 Operation Manual Download Page 79

Communications

515 HC04 - 8 June 2007

71

Printer Data Control

Some printers have limited data buffers and are therefore unable to collect 
all the print data being transmitted. The 500 Series has the capability of 
software handshaking. The Xon/Xoff characters can be used by any of the 
printer types to control the flow of data to ensure that data is not lost.

Some printers will also transmit an Xoff character in response to other 
events such as printer being off-line, print head not engaged or power being 
removed. The specific behaviour of the printer being used should be noted.

Error Messages

There are two printer error messages that can be displayed.

PAPER OUT

This message is related to the Printer Type PRN-03 TM295 Slip printer. It 
is standard procedure with this printer to check for paper status before 
printing.   If a print is attempted but there is no paper the PAPER OUT 
message will be scrolled. The instrument will continue to poll the printer for 
paper and if paper is detected before a communications timeout expires the 
print will commence. 

COMMS TIMEOUT

This message is relevant for all printer types and will be activated for the 
following conditions.

1. If the flow of data is stopped due to software or hardware handshaking 
and is not allowed to resume before the communications timeout.

2. If Printer Type is PRN-03 Slip printer and a paper status is requested but 
no response is received within the timeout period.

3. Paper Out has been detected for Printer Type PRN-03 but no paper is 
inserted within the timeout period.

When a communications timeout error has been activated the message 
COMMS TIMEOUT will be scrolled once, the request to print will be 
cleared and the instrument will return to its normal mode.

Summary of Contents for 515





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands