manualshive.com logo in svg

Contrec 515, Operation Manual

Share
Download
Contrec 515 Operation Manual Download Page 52

Instrument Calibration

44

515 HC04 - 8 June 2007

Time Settings and Data Logging

Instrument Clock

Note:

The real-time clock is part of the advanced option package.

The instrument has a real-time clock for recording logged events. The clock 
displays the time and the date. The date format can be set to European 
format (day/month/year) or American format (month/day/year). The time 
clock uses the 24-hour format.

The clock will continue to operate for up to 5 years (typically) on the 
internal battery if there is no power connected to the instrument. Therefore, 
after an interruption to the power supply, the instrument recommences 
normal operation although there will be no data recorded during the period 
without a power supply.

Note:

If there is an interruption to the power supply and the battery has 
failed, the instrument displays an error message when the power 
supply is restored. In this case, you should set the current time and 
date so that the instrument continues to log data at the correct times.

RTU

DATA

The Modbus RTU data format for the 2-register (4-byte) values can be 
set as either floating point or long integer values.

Use 

 or 

 to select FLOAT or INTEGER.

RTU

ADDR

The Modbus RTU protocol address must be in the range of 1 to 247. 
When multiple instruments (slaves) are connected to one communication 
device (master), each assigned address must be unique.

Note:

The master device uses the RTU address 0 (zero) for broadcasting 
to all connected slave units.

ASCII

ADDR

The ASCII protocol address identifies each communicating device.

The address must be in the range of 1 to 255. When multiple instruments 
(slaves) are connected to one computer (master), each assigned address 
must be unique.

FLASH

PORT

The Flash Driver Port assignment defines the communication port for 
downloading software into the instrument.

The default setting of this assignment is the RS-232 port.

Press 

 or 

 to select RS-232, RS-485, or INFRA.

 

↓

 

→ 

UNITS  PARAMS  INPUTS  OUTPUTS  ALARMS  

COMMS

 TM/LOG  SETUP  TEST  END

SET

Summary of Contents for 515





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands