manualshive.com logo in svg

Contrec 515, Operation Manual

Share
Download
Contrec 515 Operation Manual Download Page 59

Instrument Calibration

515 HC04 - 8 June 2007

51

Warning Messages

The system displays warning messages as described in the following table: 

New/Failed Battery - 
Set Time 

The real-time clock has lost the correct time because the battery has 
failed, or there is a new battery. Set the current time and date (in the 
TM/LOG menu) to clear the error message and to continue data 
logging at the correct times.

Note:

The instrument can continue operating with a failed battery, 
but the correct time will be lost if there are interruptions to the 
power supply.

Temperature Sensor 1 
Failure

The temperature sensor on analog input 1 has failed. To deactivate 
the error, the Analog Input Signal Type can be set to DEFAULT to 
use a programmed default value instead of the sensor signal.

Temperature Sensor 2 
Failure

The temperature sensor on analog input 2 has failed. To deactivate 
the error, the Analog Input Signal Type can be set to DEFAULT to 
use a programmed default value instead of the sensor signal.

Lo Range Flow Input 
Failure

The low range flow transmitter (analog input 3) has failed. 

Hi Range Flow Input 
Failure

The high range flow transmitter (analog input 4) has failed.

Diameter Ratio is out 
of Range 

The diameter ratio (beta) is out of the allowed range. The pipe and/or 
orifice diameters (specified in the Parameters menu) should be 
within the recommended limits of the DP flowmeter being used.

Temperature is Out of 
Range

The feed and/or return temperature inputs are outside of the allowed 
calculation range. 

Error Messages

Description

Warning Messages

Description

Value Has Been Set to 
Default

You have entered an invalid value for a parameter. Therefore, the 
instrument has set the default value.

Over Total Limit - 
Maximum Set

You have exceeded the maximum number of logging entries for the 
combined time bases. The instrument has set the current log setting to 
the remaining maximum number.

Already Assigned to 
Other Port

You have tried to assign a particular protocol type to more than one 
serial communication port. The instrument has set the protocol to 
NONE.

Summary of Contents for 515





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands