Contec PC-686CPCI-LV User Manual Download Page 86

Page: 86 / 118

CHAPTER 6 - BIOS SETUP

PC-686 (CPCI)-LV User’s Manual

8 Bit I/O Recovery Time

The recovery time is the length of time, measured in CPU clocks, which the system

will delay after the completion of an input/output request. This delay takes place

because the CPU is operating so much faster than the input/output bus that the CPU

must be delayed to allow for the completion of the I/O.

This item allows you to determine the recovery time allowed for 8 bit I/O.

Choices are from N/A, 1 to 8 CPU clocks.

16 Bit I/O Recovery Time

This item allows you to determine the recovery time allowed for 16 bit I/O.

Choices are from N/A, 1 to 4 CPU clocks.

Memory Hole At 15M-16M

In order to improve performance, certain space in memory can be reserved for ISA

board. This memory must be mapped into the memory space below 16MB.

The Choice: Enabled: Memory hole supported, Disabled: Memory hole not supported.

Passive Release

When Enabled, CPU to PCI bus accesses is allowed during passive release.

Otherwise, the arbiter only accepts another PCI master access to local DRAM.

The choice: Enabled, Disabled.

Delay Transaction

The chipset has an embedded 32-bit posted write buffer to support delay transactions

cycles. Select

Enabled

to support compliance with PCI specification version 2.1.

The Choice: Enabled, Disabled.

Summary of Contents for PC-686CPCI-LV























































































































Search results

Summary of Contents for PC-686CPCI-LV

Reviews:

Related manuals for PC-686CPCI-LV

Brands by name

Popular brands

Contec PC-686CPCI-LV, User Manual

Search results

Summary of Contents for PC-686CPCI-LV

Reviews:

Related manuals for PC-686CPCI-LV

Brands by name

Popular brands