Contec CNT-3204MT-LPE User Manual Download Page 70

Page: 70 / 79

5. About Software

CNT-3204MT-LPE

About Software

About Software for Windows

The counter input driver, provides functions to perform the following functions :

Function to read the current count value of a specified channel.

Function to read the current status register for a specified channel.

Function to prevent chattering based on a digital filter using hardware capabilities.

Function to preset or zero-clear the counter at the rising or falling edge of the control input signal.

Function to output a one-shot pulse to the control output signal upon detection of a count match or

error.

Function to sample count values using bus mastering in sync with the specified external clock or

internal clock.

For details, refer to the help file.

Accessing the Help File

The method to use in accessing the help file varies slightly depending on the version of the driver (the

development environment) that is installed.

From the Start menu, click "CONTEC API-PAC(W32)" - "API-TOOL(WDM) HELP".

When this link does not exist,

From the Start menu, click "CONTEC API-PAC(W32)" - "API-CNT(WDM)" - "API-CNT(WDM)

HELP".

* For the API-CNT(98/PC) driver,
From the Start menu, click "CONTEC API-PAC(W32)" - "API-CNT(98/PC)" - "API-CNT HELP".

Summary of Contents for CNT-3204MT-LPE
















































































Search results

Summary of Contents for CNT-3204MT-LPE

Reviews:

Related manuals for CNT-3204MT-LPE

Brands by name

Popular brands

Contec CNT-3204MT-LPE, User Manual

Search results

Summary of Contents for CNT-3204MT-LPE

Reviews:

Related manuals for CNT-3204MT-LPE

Brands by name

Popular brands