Contec CNT-3204MT-LPE User Manual Download Page 67 | Manualshive

Page: 67 / 79

background image

4. Functions

60

CNT-3204MT-LPE

Status input

This product has the following status.

Pulse signal input states

The phase-A, phase-B, and phase-Z input states and count directions can be checked by their status.

Control input signal states

The control input signal states can be checked by the status.

Error

Abnormal input error

An abnormal input error occurs when the counter input signal changes on the A and B phases

simultaneously. A status is latched to indicate that this error has occurred and can be cleared by

software.

Digital filter error

When a signal faster than the digital filter setting is input to phase-A or B, it is reported as a digital filter
error. The status is latched and cleared by software.

Carry/Borrow

Carry

The 32-bit counter is set to [1] when incremented from its maximum value FFFFFFFFh - 0h.

Borrow

The counter is set to [1] when decremented from 0h - FFFFFFFFh.

Count match

A count match (to register 0), count match (to register 1), incremental count match, or decremental
count match for each channel can be checked by the status.

«
...
65
66
67
68
69
...
»

Summary of Contents for CNT-3204MT-LPE
















































































Reviews:

No comments

Related manuals for CNT-3204MT-LPE

Brand: XDS Pages: 99

Brand: Xilica Audio Design Pages: 30

CompactPCI CC8-BLUES

Brand: EKF Electronik Pages: 52

NI WLS/ENET-9163

Brand: National Instruments Pages: 36

Brand: mikroElektronika Pages: 2

Brand: ekwb Pages: 11

FireWire 800 ExpressCard 34

Brand: LaCie Pages: 24

Brand: SilverStone Pages: 28

AirBridge VS-YOFIMN-000

Brand: Vivint Pages: 2

Brand: IBM Pages: 242

Brand: NI Pages: 8

Brand: Paradyne Pages: 10

Brand: Bdcom Pages: 25

Brand: TRENDnet Pages: 2

Brand: Behringer Pages: 12

Brand: Zmotion Pages: 56

Brand: ICP DAS USA Pages: 60

Brand: HeimVision Pages: 167

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands